top of page

This cropped, chin-length shag has loose, allover layers for volume with additional length at the crown, top, and sides, giving this silhouette its versatile looks. Choppy, eyelash-grazing bangs are razor-cut for It Girl cool.

 

Made with Tru2Life® heat-friendly synthetic hair that can be flat-ironed, curled or blown out. (See packaging insert for complete directions.)

 

Cap Size: Average

 

Front: 4″ Crown: 5″ Sides: 5″ Back: 3″ Nape: 1¾” Color Shown: R3025S+ Glazed Cinnamon

 

Whispy Cut

HEAT FRIENDLY CARE

WE RECOMMEND WASHING YOUR ALTERNATIVE HAIR EVERY 6-8 WEARS

 

CLEANSE & CONDITION

•  Before washing, gently remove any tangles using your our Wide Tooth Comb ONLY
•  Wet hair completely using cool running water 
•  Gently lather the hair with a small amount of our HairUWear Shampoo, making sure that the hair is traveling in the same direction. DO NOT rub hair; this will cause tangling
•  Rinse thoroughly under cool running water until water runs clear 
•  Wrap wig or hairpiece in a towel and gently pat dry  
•  Gently detangle hair using Wide Tooth Comb
•  Spray with our Leave-In Conditioning Spray (3-5 pumps) keeping away from base 

 

DRY & STYLE

•  Allow wig or hairpiece to air dry naturally by placing on a plastic or wire wig stand. It's best not to blow dry

•  Air drying your wig will give the best results. The fiber will dry fastest; be sure the cap is completely dry before wearing, storing, or displaying

•  Apply our HairUWear Leave-in Conditioner + Detangler, (3-5 pumps) focusing on the bottom half of wig or hairpiece. Gently comb through using your Wide Tooth Comb

•  ONLY our wide tooth comb is used on your Heat Friendly fiber. Other tools will cause frizzing/tangling 

•  Heat Friendly fiber can withstand heat up to 350° F, however, K's recommends working at 270°-280° F

•  It is recommended to use professional grade heat styling tools with digital temperature settings to control heat

 

CURL & FLAT IRON

•  Heat your curling or flat iron to 270°-280° F

•  Using your Wide Tooth Comb, gently comb hair free of tangles

•  Starting at the nape, take ½ inch-1.5 inch sections of hair (smaller sections=tighter curls, larger sections=looser curls)

•  Spray our Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)

 

CURL

•  Gather hair into curling iron, smooth through to the ends. Roll iron up towards base of wig or hairpiece, staying 1-2 inches away

 •  Hold for 10-15 seconds, then turn the tip of iron toward the ground and release curl into palm of hand

•  Holding curl in one hand, gather up towards base and secure curl with a small metal clip (like a pin curl)

•  Allow curl to cool completely (about 5 minutes); remove clip and let curl hang naturally

 

FLAT IRON

•  Starting at the nape, take ½ inch-1.5 inch sections 

•  Spray our Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)

•  Slowly smooth flat iron down through ends; keep hair smooth by following behind the flat iron with your Wide Tooth Comb

•  Allow hair to hang naturally and cool completely

 

TIPS

•  All synthetic fibers can tangle and frizz with wear. It is important that the frizz is corrected early to avoid permanent damage to the fiber. Use your flat iron to smooth any frizz before washing
•  We recommend using our HairUWear Leave-in Conditioner + Detangler with a Wide Tooth Comb DAILY to detangle your Heat Friendly wig. This is especially important with the mid-length to long length Heat Friendly wigs or hairpieces
•  To add texture and definition, use a small amount of our Piece Out Contour Fiber Crème and apply using fingertips 

You May Also Like

bottom of page